(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- [Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
2-Layer Soft Fluoropolymer Tubing TQ Series (Part Numbers)
Tubing with a 2-layer structure.
[Features]
· Fluids such as solvents are transferred by flexible piping with superior abrasion resistance.
· Wearing of outer layer tube: Reduced to 1/30.
· Flexibility: Improved by up to 55% (*1). * 1: Compared with SMC Fluoropolymer Tubing / TL (ø6 [6‑mm diameter] × ø4 [4‑mm diameter]).
[Applications]
· Semiconductors, food, medical, machine tools.
(i)Caution
- The maximum operating pressure values listed are at 20°C. See the catalog for details.
- For specifications and details, please refer to the catalog.
Features Of 2-Layer Soft Fluoropolymer Tubing TQ Series
How to measure the minimum bending radius
Bend the tube into a U shape at a temperature of 20°C. Fix one end and bend the loop gradually at 100 mm/min. Measure 2R when the tube breaks or is crushed.
Applicable Fluid List
Fluids in the list below are chemically inert to tubing material. Possible physical effects may occur such as penetration and swelling due to temperature, pressure and chemical density. To use tubing in a solvent environment, tests should be performed under the same environment to ensure no problem occurs under the operating environment.
| Chemical | Inner layer | Outer layer |
|---|---|---|
| Special fluoropolymer | Special nylon resin | |
| Hydrochloric acid | ○ | △ |
| Sulfuric acid | ○ | △ |
| Nitric acid | ○ | × |
| Caustic soda | ○ | △ |
| Caustic potash | ○ | △ |
| Ammonia hydroxide | ○ | ○ |
| Hydrogen peroxide | ○ | △ |
| Water | ○ | ○ |
| Phenol | ○ | × |
| Benzene | ○ | △ |
| Toluene | ○ | △ |
| Xylene | ○ | △ |
| Carbon tetrachloride | ○ | × |
| Acetone | ○ | △ |
| Methyl ethyl ketone | ○ | △ |
| Chemical | Inner layer | Outer layer |
|---|---|---|
| Special fluoropolymer | Special nylon resin | |
| Citric acid | ○ | △ |
| Stearic acid | ○ | △ |
| Formic acid | ○ | △ |
| Ethyl acetate | ○ | ○ |
| Butyl acetate | ○ | △ |
| Methyl alcohol | ○ | ○ |
| Ethyl alcohol | ○ | ○ |
| Butyl alcohol | ○ | ○ |
| Isopropyl alcohol | ○ | ○ |
| Cellosolve | △ | △ |
| Hexane | ○ | △ |
| Cyclohexane | ○ | △ |
| Mineral oil ASTM No. 3 | ○ | ○ |
| Naphtha | ○ | ○ |
- 1. "Chemically inert" means to not cause any chemical reaction.
- 2. Criteria: ◯ Applicable, △ Not recommended, × Inapplicable
- 3. Applicable Fluid List shows the reference values based on test results performed under specific conditions. Application to products is not guaranteed.
- 4. Applicable Fluid List is for tube materials. For use in environments containing solvents, please contact SMC.
Series List And Specifications
| Nominal | TQ0425 | TQ0604 | TQ0806 | TQ1008 | TQ1209 | |
|---|---|---|---|---|---|---|
| Outer diameter (mm) | 4 | 6 | 8 | 10 | 12 | |
| Inner diameter (mm) | 2.5 | 4 | 6 | 8 | 9 | |
| Roll | 20 m | ● | ● | ● | ● | ● |
| 100 m | ● | ● | ● | ● | ● | |
| ColorNote 1) | Translucent (material color) | |||||
| FluidNote 2) | Air, water, inert gas, solvent | |||||
| Applicable fittingsNote 3) Note 7) | Insert fittings KF, KFG2, VCK Series Miniature fittings M, MS Series (Hose-nipple type) Fluoropolymer fittings LQ1, LQ3Note 6) | |||||
| Maximum operating pressureNote 4) MPa | 20°C | 2.0 | 1.9 | 1.5 | 1.1 | 1.2 |
| Minimum bending radius (tube close bend radius)Note 5) mm | 4 | 9 | 26 | 42 | 37 | |
| Fluid temperature (fixed usage) | Air, inert gas: -20 to 100°C / Water, solvent: 0 to 70°C (No freezing) | |||||
| Material | Inner layer: special fluoropolymer, Outer layer: special nylon resin | |||||
- 1. There may be plasticizer (white powder) deposits on the external surface of the tube. Please exercise caution when using this item in a clean room. Otherwise, the clean level may decrease.
- 2. When solvent is used, make sure to test in the same environment as the actual operating environment, and confirm that no problem will occur under the operating conditions. The standard values of the Applicable Fluid List below are the reference values based on the results of tests performed under specific conditions. The product can be physically affected by temperature, pressure, chemical density, etc., causing permeation or swelling, and this may cause some problems.
- 3. Perform periodic maintenance inspections. If leakage continues to occur after tightening, replace the tube with a new one. If the tube will be used in a location where it moves, perform a test to make sure no problems occur under the actual operating conditions. When the product is used with motion for a long time, or at a high temperature, the tubes may leak due to deterioration of the materials.
- 4. Observe the lesser value of the maximum operating pressure between the tubing and fittings. The surge pressure must not exceed the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to tubes and fittings. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tube bursting.
- 5. The minimum bend radius (tube close bend radius) is not guaranteed. The value of 2R is measured with a bent or flattened tube.
- 6. For the installation of fluoropolymer fitting LQ1 and LQ3, please contact SMC.
- 7. A fitting that seals the outer diameter of the tube such as a one-touch fitting is not applicable since it is in contact with the wetted part of the external layer nylon material.
Maximum operating pressure
| Temperature (°C) | TQ0425 | TQ0604 | TQ0806 | TQ1008 | TQ1209 |
|---|---|---|---|---|---|
| -20 to 20 | 2.0 | 1.9 | 1.5 | 1.1 | 1.2 |
| 30 | 1.7 | 1.6 | 1.2 | 0.9 | 1.0 |
| 40 | 1.4 | 1.4 | 1.0 | 0.8 | 0.9 |
| 50 | 1.2 | 1.1 | 0.8 | 0.6 | 0.8 |
| 60 | 1.1 | 1.0 | 0.7 | 0.5 | 0.7 |
| 70 | 1.0 | 0.9 | 0.6 | 0.4 | 0.6 |
| 80 | 0.9 | 0.8 | 0.5 | 0.4 | 0.5 |
| 90 | 0.8 | 0.7 | 0.4 | 0.3 | 0.4 |
| 100 | 0.7 | 0.6 | 0.4 | 0.3 | 0.3 |
Unit: MPa
| Part Number |
|---|
| TQ0425-20 |
| TQ0425-100 |
| TQ0604-20 |
| TQ0604-100 |
| TQ0806-20 |
| TQ0806-100 |
| TQ1008-20 |
| TQ1008-100 |
| TQ1209-20 |
| TQ1209-100 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Outer Dia. D (Ø) | Inner Dia. d (Ø) | Outer Diameter [Category] | I.D. [Category] | Min. Bend Radius (mm) | Bundle winding length (m) | Maximum operating pressure (MPa) |
|---|---|---|---|---|---|---|---|---|---|---|---|
MYR 456.87 | 1 Piece(s) | 43 Day(s) | 4 | 2.5 | Up to 4 | ~3 | - | 20 | 2 | ||
MYR 1,384.24 | 1 Piece(s) | 14 Day(s) or more | 4 | 2.5 | Up to 4 | ~3 | - | 100 | 2 | ||
MYR 603.87 | 1 Piece(s) | 43 Day(s) | 6 | 4 | Up to 6 | ~4 | - | 20 | 1.9 | ||
MYR 1,634.80 | 1 Piece(s) | 9 Day(s) or more | 6 | 4 | Up to 6 | ~4 | - | 100 | 1.9 | ||
MYR 732.08 | 1 Piece(s) | 3 Day(s) | 8 | 6 | Up to 8 | ~6 | 26 | 20 | 1.5 | ||
MYR 2,334.97 | 1 Piece(s) | 14 Day(s) or more | 8 | 6 | Up to 8 | ~6 | 26 | 100 | 1.5 | ||
MYR 644.23 | 1 Piece(s) | 5 Day(s) or more | 10 | 8 | Up to 10 | ~8 | - | 20 | 1.1 | ||
MYR 3,378.51 | 1 Piece(s) | 14 Day(s) or more | 10 | 8 | Up to 10 | ~8 | - | 100 | 1.1 | ||
MYR 1,118.65 | 1 Piece(s) | 9 Day(s) or more | 12 | 9 | Up to 15 | ~9 | - | 20 | 1.2 | ||
MYR 6,505.93 | 1 Piece(s) | 14 Day(s) or more | 12 | 9 | Up to 15 | ~9 | - | 100 | 1.2 |
Loading...
Basic Information
| Applicable Fluid | Water / Air | Color | Translucent (Material Color) | Type | Straight |
|---|---|---|---|---|---|
| Operating Environment | Standard | Cutting Service Availability | No | Material | Inner Layer: Special Fluoropolymer, Outer Layer: Special Nylon Resin |
| Operating temperature(°C) | Air, Inert Gas: -20 to 100 / Water, Solvent: 0 to 70 (Do Not Freeze) |
Specification/Dimensions
-
Outer Dia. D(Ø)
-
Inner Dia. d(Ø)
-
Outer Diameter [Category]
-
I.D. [Category]
-
Bundle winding length(m)
-
Maximum operating pressure(MPa)
- 1.1
- 1.2
- 1.5
- 1.9
- 2
-
type
- TQ
Days to Ship
-
- All
- 3 Day(s) or Less
- 5 Day(s) or Less
- 9 Day(s) or Less
- 14 Day(s) or Less
- 43 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Additional Products in this Category
- Silicone Tube 10 m/20 m (The Length Can Be Specified in Increments of 0.5 mm)
- Urethane Tubes
- Jumbo Curled Hose
- Urethane Tube U2 for General Air Pressure
- Flexible Fluororesin 2 Layer Tube for Coating (Flexibility and Abrasion Resistance) TES
- Fluoropolymer Tube TA, Clean, Heat Resistant, Cold Resistant, Chemical Resistant
- Junron AS1 (Inch Series Flexible Nylon Tube)
- Multi-Holder TMA Series
Tech Support
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy