(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- [Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
Safety Door Switches (E-MSMD4CF-K2)
- Economy
- Volume Discount
Part Number
Configured Part Number is shown.
E-MSMD4CF-K2
· Suitable for both standard and micro loads.
· Simple installation and wiring, labor-saving, and easy to replace.
| Lock Dimensions | Key Dimensions |
| E-MSMD4□F | T type E-MSMD2-K1 |
 |  |
| L type E-MSMD2-K2 | |
 |
■ Minimum radius and safety distance for operating key insertion and swing door
When installing the operating key, make sure it is within 1 mm of the center of the operating keyhole. If the operating key is offset from this position or inserted at an angle, it may cause accelerated wear or breakage.
Note: Please follow the specified insertion radius for the operating key and insert it vertically into the keyhole.
| Key installation type | E-MSMD2-K1 | E-MSMD2-K2 |
| A operation key mounting surface | 44-46.5 mm | 40-42.5 mm |
| B operation key mounting surface | 54.5-57 mm | 50.5-53 mm |
| Horizontal direction radius R | ≥ 200 mm | ≥ 200 mm |
| Vertical radius R | ≥ 200 mm | ≥ 200 mm |
■ Mounting holes
· Please use M4 screws and spring washers to install the switch and operating key, and tighten them with the appropriate torque.
· For safety, please use screws that cannot be easily removed or take similar measures to prevent the switch and operating key from being easily removed.
· As shown below, you can use two bolts with a height of 4.8 mm or less and a diameter of 4 mm, inserted into the holes at the bottom of the switch, to enable four-point mounting for a more secure installation.
| Protection Rating | IP67 | |
| Material | PA66 flame retardant | |
| Mechanical life | Over 1,000,000 cycles | |
| Electrical life | Over 150,000 cycles | |
| Type of use | AC-15 | DC-13 |
| Rated operational voltage (Ue) | 240V | 24V |
| Rated operational current (Ie) | 3A | 2A |
| Operating characteristics | ||
| Positive opening force | 60N | |
| Minimum positive opening travel | 10 mm or more | |
| Operating speed | 0.1 m to 0.5 m/s | |
| Permissible operating frequency | Maximum 20 operations/minute | |
| Environment | ||
| Operating ambient temperature | -10°C to +60°C (no freezing) | |
| Operating ambient humidity | 85% RH or less | |
| Electrical | ||
| Contact resistance | 200 mΩ or less | |
| Rated insulation voltage (Ui) | 300V | |
| Electric shock protection class | Class II (double insulation) | |
| Impulse withstand voltage (EN60947-5-1) | 2.5 kV | |
| Insulation resistance | Above 100MΩ (at 500 V DC or below) | |
| Short-circuit protection device | Requires a quick-blow fuse, 10 A, 250 V | |
| Vibration resistance | 10-55Hz, double amplitude 1.5 mm | |
| Shock resistance | Durability 1000 m/s2 | |
| Conditional short-circuit current | 100 A (EN60947-5-1) | |
| Contact gap | 2 x 2 mm or more | |
■ Product structure
It is recommended to use wire sizes of 0.5 to 1.5 mm². Please refer to the above diagram for wire length. The waterproof connector ensures IP67 protection level, and shielding tape can be wrapped around the threaded part.
When using crimp terminals, the total length of the terminal should be within 19 mm, and the thickness should be less than 0.5 mm.
The illustration shows the state when the operation key is inserted.
| Door Lock Model | Contact Type | Contact Form | Operation Mode |
| E-MSMD4CF | 2NC/1NO |  |  |
| E-MSMD4DF | 3NC |  |  |
| Model | Contact Type | Locking Method | Conduit Port Size | Head Material | Rated Operating Voltage/Current |
| E-MSMD4CF | 2NC/1NO | Mechanical locking | M20 | PA66 | 24 V/2 A |
| E-MSMD4DF | 3NC |
Two types of keys available
| Combination models including operation key | Door Lock Model | Operating key model | Contact Type | Key material | Operating key insertion force (Max) | Operating key withdrawal force (Max) | Total travel - TT | Pre-travel - PT |
| E-MSMD4CF-K1 | E-MSMD4CF | E-MSMD2-K1 (T type) | 2NC/1NO | SUS201 | 15N | 50N | 28 mm | 6±3 mm |
| E-MSMD4DF-K1 | E-MSMD4DF | 3NC | ||||||
| E-MSMD4CF-K2 | E-MSMD4CF | E-MSMD2-K2 (L type) | 2NC/1NO | |||||
| E-MSMD4DF-K2 | E-MSMD4DF | 3NC |
· When loosening screws using an electric screwdriver or similar tool by pressing the screw head, do not over-loosen the screw to the point where the threads disengage.
· Otherwise, the end of the threads may be damaged.
· Do not use the switch as a stopper. To ensure that the base of the operating key does not touch the switch head, be sure to install the limit stopper as shown below, and adjust the stopper so that the operating key stays within the set area of the base (1–3.5 mm).
· Do not subject the switch to impacts exceeding its shock resistance value (1000 m/s²).
Installation on left-side movable door
· Do not immerse the switch in oil or water, or use the switch in locations where it is continuously exposed to oil or water splashes. Otherwise, oil or water may enter the inside of the switch. (The IP67 protection rating of the switch specifies the amount of water ingress after the switch is immersed in water for a certain period of time.)
· After wiring work is completed, the cover must be installed before using the switch. In addition, do not operate the switch while the cover is open. Otherwise, electric shock may occur.
· When switching a standard load (250 V AC, 3 A), do not operate two or more circuits at the same time. Otherwise, the insulation performance may be reduced.
5. About the operating key
· You must use the designated operating key. The head is designed so that it cannot be operated with a screwdriver or similar tool. Operating the switch with tools other than the designated operating key may damage the switch or compromise the safety of the equipment.
· You must use the designated operating key; using any other key may damage the switch or compromise system safety.
· If excessive force is applied to the tip of the key or if it is dropped while the operating key is inserted into the switch, the key may become deformed or the switch may be damaged.
6. Changing the head orientation
· You can adjust the switch head by loosening the mounting screws at the four corners of the switch head and rotate it in any of the four directions. Please make sure that no foreign objects enter the switch head.
· Do not insert or remove the operation key when the switch head is removed. Otherwise, the operation key may not be able to be inserted.
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
| Part Number |
|---|
| E-MSMD4CF-K2 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Acquired Standards | Contact Type | Operating Key | Usage Method | Operating Key Material |
|---|---|---|---|---|---|---|---|---|---|
MYR 71.22 | 1 Piece(s) | Available | 6 Day(s) | - | 2NC/1NO | E-MSMD2-K2 (vertical installation) | Mechanical door lock, operating key kit | SUS201 |
Loading...
Basic Information
| Rated Operating Voltage(V) | 24 | Rated operating current(A) | 2 | Safety Door Lock Conduit Port Size | M20 |
|---|---|---|---|---|---|
| Safety Door Lock Head Material | PA66 | Locking Method | Mechanical locking | Safety Door Lock Body Material | PA66 |
| Safety Door Lock Locking Force | 50N |
Please check the type/dimensions/specifications of the part E-MSMD4CF-K2 in the Safety Door Switches series.
Specification/Dimensions
-
Contact Type
- 2NC/1NO
- 3NC
-
Operating Key
- E-MSMD2-K1 (horizontal installation)
- E-MSMD2-K2 (vertical installation)
-
Usage Method
- Mechanical door lock, operating key kit
- Product does not include operating key
-
Operating Key Material
- SUS201
-
CAD
- 2D
- 3D
Days to Ship
-
- All
- 6 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Products like this...
| Part Number |
|---|
| E-MSMD4CF |
| E-MSMD4CF-K1 |
| E-MSMD4DF |
| E-MSMD4DF-K1 |
| E-MSMD4DF-K2 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Acquired Standards | Contact Type | Operating Key | Usage Method | Operating Key Material |
|---|---|---|---|---|---|---|---|---|---|
MYR 63.36 | 1 Piece(s) | Available | 6 Day(s) | CE | 2NC/1NO | - | Product does not include operating key | - | |
MYR 71.22 | 1 Piece(s) | Available | 6 Day(s) | - | 2NC/1NO | E-MSMD2-K1 (horizontal installation) | Mechanical door lock, operating key kit | SUS201 | |
MYR 63.38 | 1 Piece(s) | Available | 6 Day(s) | CE | 3NC | - | Product does not include operating key | - | |
MYR 71.22 | 1 Piece(s) | Available | 6 Day(s) | - | 3NC | E-MSMD2-K1 (horizontal installation) | Mechanical door lock, operating key kit | SUS201 | |
MYR 70.64 | 1 Piece(s) | Available | 6 Day(s) | - | 3NC | E-MSMD2-K2 (vertical installation) | Mechanical door lock, operating key kit | SUS201 |
Additional Products in this Category
- Small Enclosed Switch [D4E-□N]
- Slim Type Safety / Door Switch [D4GS-N]
- Small Safety Limit Switch [D4F]
- Small Electromagnetic Lock Safety Door Switch [D4NL]
- Solenoid Lock / Safety Door Switch [D4BL]
- Small Solenoid Lock / Safety Door Switch [D4SL-N]
- Oil Resistant Limit Switch [D4ER-□N]
- Microswitch, S-3-BE Series
Tech Support
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy