[Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
[Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

[Clean & Pack]8 Series (Slot Width 10 mm) - For 1 Slot, Extruded Eccentric Brackets (SL-HBLTH8)

Volume Discount

Three types of cleaning methods are available: degreasing, precision cleaning, and electrolytic polishing + precision cleaning. They can be ordered from one piece with the standard part number.
This eliminates the need for customer cleaning or outsourced cleaning, reducing the amount of time and effort required.

■ Part Number for Clean & Pack Products

· Degreasing (Anti-rust single packing)	: Part Number SL-□□
· Precision cleaning (Degassing double packing)	: Part Number SH-□□
· Electrolytic polishing + precision cleaning (Degassing double packing)	: Part Number SHD-□□

Product Part Number	Cleaning Method	Packaging Type	Effects Compared to Uncleaned Product	Environment (Standard)	Process
SL-□□	Degreasing	Anti-rust packing	Oil removal	General environment	Regular assembly process
					Post battery assembly process
SH-□□	Precision cleaning	Degassing double packing	Oil removal Dust removal	Clean environment (Class 10 to 1,000)	Battery assembly process
					LCD-related post assembly process
					In-vehicle camera assembly process
SHD-□□	Electrolytic polishing + precision cleaning	Degassing double packing	Oil removal Dust removal Outgas reduction	Vacuum environment Clean environment (Class 10 to 1,000)	Pre-semiconductor process
					Liquid crystal deposition process
					Pre-OLED process

■ Notes
Cleaning also removes rust prevention oil, which may make the product more susceptible to rusting than an uncleaned product.
Please be careful about the application location and storage environment.

Hole positions are offset. Applicable to the panels of both 3 mm and 5 mm thickness.

(i)Caution

Cleaning also removes rust prevention oil, which may make the product more susceptible to rusting than an uncleaned product.
Please be careful about the application location and storage environment.

Part Number

Configured Part Number is shown.

SL-HBLTH8

Drawing/Specifications
3D Preview
Part Numbers
More Information

Part Number	[ M ] Material	[ S ] Surface treatment	Cleaning Method
			Cleaning Method	Cleaning Environment	Packaging Type	Packing Environment
SL-HBLTH8	A6N01SS−T5	Anodize	Degreasing	General environment	Anti-rust packing	General environment
SH-HBLTH8			Precision cleaning	Class 1,000	Degassing double packing	Class 10

[!] Products are packed by order quantity. Ex. If the order is for 20 pieces, they are packed in one package (incl. 20 pieces).
[!] See the details of degreasing, precision cleaning, and electrolytic polishing shown at the bottom of the

specification table.

Specification Table

Part Number

SL-HBLTH8

Part Number	Mass	Applicable Screw, T Nut				Allowable Load
	(g)	Bolt	Quantity	T Nut	Quantity	(N)
SL-HBLTH8	68	SCB8-20	2	HNTTSN8-8	2	2058
SH-HBLTH8

[ ! ] If you would like to order screws and nuts as a set, please check the alteration "Applicable Screw, Nut Set."

Alterations

Part Number	—	(C·SST·SSU·SSP)
SL-HBLTH8	—	SST
SL-HBLTH8	—	C-SST

Alterations	Code	Spec.	Applicable Bracket
Mounting Hole Alteration for Cover	C	Adds taps on a bracket for cover mounting. (M5 on Both Sides) (Mounting Screw HCBM)	HBKTS8
			NBLTS8
			HBLTS8
			CHBLTS8
			HBLTH8

Alterations

Code

Spec.

Applicable Bracket

Applicable Bolts
and Nuts Set

SST
(Stainless Steel)
SSU
(Pre-Assembly Insertion
Spring Nut
Stainless Steel)
SSP
(Post-Assembly Insertion
Spring Nut
Stainless Steel)

Applicable screws and nuts for fixing the brackets on extrusions come in a set.

(Example) When HBLTS8 is specified

	Bolt		Nut
Code	Part Number	Quantity	Part Number	Quantity
SST	SCB8－20	2	HNTTSN8－8	2
SSU	SCB8－20		SHNTU8－8
SSP	SCB8－20		SHNTP8－8

[ ! ] When specifying other than HBLTS8, check for the applicable screws and nuts respectively.

—

HBKTST8

HBKTS8

HBKTSB8

NBLTS8

HBLTS8

HBLTSB8

CHBLTS8

HBLTH8

[ ! ] Screws for black anodized brackets are made of HCBMTB (Trivalent Chromate Black).
[ ! ] The part numbers are those of the products before cleaning.

Alteration Details

■Mounting Hole Alteration for Cover (-C)

M5 tapped holes can be added on both sides.
Alteration Part Number Example: HBLTH8-C

■Set of applicable Screws and Nuts Details

Alteration part number	Bolt		Nut
Alteration part number	Part Number	Material	Type	Part Number	Material	Stopper
SST	SCB8-20	Stainless Steel	Pre-Assembly	HNTTSN8-8	Stainless Steel	None
SSU	SCB8-20	Stainless Steel	Pre-Assembly	SHNTU8-8	Stainless Steel	Provided
SSP	SCB8-20	Stainless Steel	Post-Assembly	SHNTP8-8	Stainless Steel	Provided

App. Example

Hole positions are offset. Applicable to the panels of both 3 mm and 5 mm thickness.

[ ! ] They can be combined with cover plates of thickness 3 mm and 5 mm.

Mounting Hole Alteration (-C) for Cover is recommended when mounting the panel to the bracket.
Panel Mounting Screws: HCBM

■Difference between Extruded Brackets and Tabbed Brackets

[This Product]Extruded Brackets	·The extruded brackets are made of A6N01SS-T5, manufactured by aluminum extrusion. Surfaces are anodized. ·Suitable when appearance well balanced with the extrusions is desired. Designed to prevent dust from building up. ·Suitable for the areas where the strength is required because it is stronger than the tabbed brackets.
Tabbed Brackets	·The tabbed brackets are molded brackets made of material ADC12. Since it is not basically anodized, it is less expensive than extruded brackets of the same size. ·Since the tabs stop rotating the brackets when tightening, work efficiency is improved. ·Various types of brackets with additional functions are available.

Technical Information

■ Perpendicularity

Perpendicularity of Extruded Brackets is manufactured within ±1° tolerance based on JIS Standard H4100 Special Grade.
For applications where perpendicularly is important, use Perpendicularly Machined Type.
(For 8 Series: Perpendicularity 0.03 and 0.06 are available.)

■How to Specify Allowable Load of Bracket

This represents the allowable load per bracket for the extrusion assembly structured by bridging a beam extrusion between two vertical extrusions and then, attaching a bracket just below the bottom face of each end of the beam extrusion.
Allowable Load here means the load under which the bracket can stays at its position (without fracturing or sliding), after all of its mounting holes are fixed with screws.

Cleaning Process

· Degreasing (Part Number: SL-□□)

* Stainless steel products may be used with alkaline hot pure water. There is no change in cleanliness.
* If the surface treatment is low-temperature black chrome plating, IPA cleaning will be applied.

Working Environment: General environment
Hydrocarbon cleaning Ro water cleaning Neutral Detergent Cleaning		High-pressure jet washing (Ro water) followed by pure water cleaning		Oil-free Compressor Used		Anti-rust single packing

· Precision cleaning (Part Number: SH-□□)

				Working Environment: Class 1,000				Working Environment: Class 10
Hydrocarbon cleaning Ro water cleaning Neutral Detergent Cleaning		High-pressure jet washing (Ro water) followed by pure water (10 MΩ·cm) cleaning		Use pure water (13 MΩ·cm)		Use nitrogen blow		Conducted on a clean bench in a Class 10 clean environment

· Electrolytic polishing + precision cleaning (Part Number: SHD-□□)

						Working Environment: Class 1,000				Working Environment: Class 10
Hydrocarbon cleaning Ro water cleaning Neutral Detergent Cleaning		Electrolytic polishing with an electrolytic polishing layer according to the material		High-pressure jet washing (Ro water) followed by pure water (10 MΩ·cm) cleaning		Use warm pure water (13 MΩ·cm)		Use nitrogen blow		Conducted on a clean bench in a Class 10 clean environment

Packaging Example

For degreasing:
(Part Number: SL-□□)

Depending on some products and dimensions,
packaging type may vary.

For precision cleaning or electrolytic polishing + precision cleaning:
(Part Number: SH-□□/SHD-□□)

[ ! ] Both the first and second layer packaging are degassed.

Cleaning Effectiveness / Recommended Environment for Use

Cleaning Method	Product Part Number	Packaging Type	Effects Compared to Uncleaned Product	Environment (Standard)	Use Case and Process
Degreasing	SL-□□	Anti-rust packing	Oil removal	General environment	Regular assembly process
Degreasing	SL-□□	Anti-rust packing	Oil removal	General environment	Post battery assembly process
Precision cleaning	SH-□□	Degassing double packing	Oil removal Dust removal	Clean environment (Class 10 to 1,000)	Battery assembly process
					LCD-related post assembly process
					In-vehicle camera assembly process
Electrolytic polishing + precision cleaning	SHD-□□	Degassing double packing	Oil removal Dust removal Outgas reduction	Vacuum environment Clean environment (Class 10 to 1,000)	Pre-semiconductor process
					Liquid crystal deposition process
					Pre-OLED process

Part Number

CAD Data download and 3D preview are not available because the part number has not yet been determined.

*In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.

CAD Download

: 30; 45; 60

Part Number
SL-HBLTH8

Part Number	Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	Cleaning Method	Mounting Hole Alteration for Covers	Accessory
	MYR 23.46	1 Piece(s)	Available	6 Day(s) or more	Degreasing	N/A	N/A

App. Example

[ ! ] They can be combined with cover plates of thickness 3 mm and 5 mm.

Basic Information

Bracket Type	Extruded Brackets	Environmentally Friendly	RoHS compliant (10 substances)	Properties / applications	Clean washing
Tab Position	Not Tabbed	Compatible Extrusion Width(mm)	40	Compatible No. of Slots	1 Slot
Perpendicularity	No Standard	Series	MISUMI Brackets for 8 Series (Extrusion Slot Width 10mm)	Additional Functions (Extruded Bracket)	Eccentricity
Material	A6N01SS-T5	Surface Treatment	Anodizing	Extrusion No.	8
Extrusion Size	for 40・80	Bracket Type	Eccentric Brackets	Applicable Screws	M8 bolt
Number of Extrusion Connection Holes	2

Please check the type/dimensions/specifications of the part SL-HBLTH8 in the [Clean & Pack]8 Series (Slot Width 10 mm) - For 1 Slot, Extruded Eccentric Brackets series.

Configure

1 Part Numbers

View Part Numbers

Configure Remaining Specifications

Completed

Specification/Dimensions

type
- SH-HBLTH8
- SL-HBLTH8
Clear
Cleaning Method
- Degreasing
- Precision Cleaning
Clear
Mounting Hole Alteration for Covers
- C (Cover mounting tapping)
- N/A
Clear
Accessory
- N/A
- SSP (Stainless steel bolt / post-assembly insertion spring nut set)
- SST (Stainless steel bolt / nut set)
- SSU (Stainless steel bolt / pre-assembly insertion spring nut set)
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

6 Day(s) or Less
Clear

Specify Alterations

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Products like this...

Part Number
SH-HBLTH8-C-SST
SH-HBLTH8-C-SSU
SH-HBLTH8-SSP
SL-HBLTH8-C
SL-HBLTH8-C-SSP
SL-HBLTH8-C-SST

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	Cleaning Method	Mounting Hole Alteration for Covers	Accessory
MYR 34.03	1 Piece(s)	Available	6 Day(s) or more	Precision Cleaning	C (Cover mounting tapping)	SST (Stainless steel bolt / nut set)
MYR 37.07	1 Piece(s)	Available	6 Day(s) or more	Precision Cleaning	C (Cover mounting tapping)	SSU (Stainless steel bolt / pre-assembly insertion spring nut set)
MYR 34.57	1 Piece(s)	Available	6 Day(s) or more	Precision Cleaning	N/A	SSP (Stainless steel bolt / post-assembly insertion spring nut set)
MYR 24.17	1 Piece(s)	Available	6 Day(s) or more	Degreasing	C (Cover mounting tapping)	N/A
MYR 35.28	1 Piece(s)	Available	6 Day(s) or more	Degreasing	C (Cover mounting tapping)	SSP (Stainless steel bolt / post-assembly insertion spring nut set)
MYR 33.32	1 Piece(s)	Available	6 Day(s) or more	Degreasing	C (Cover mounting tapping)	SST (Stainless steel bolt / nut set)

Additional Products in this Category

Tech Support

: Technical Inquiry

How can we improve?

[Clean & Pack]8 Series (Slot Width 10 mm) - For 1 Slot, Extruded Eccentric Brackets (SL-HBLTH8)

(i)Caution

Specification Table

Alterations

Alteration Details

App. Example

Technical Information

Part Number

App. Example

Basic Information

Configure

Specification/Dimensions

type

Cleaning Method

Mounting Hole Alteration for Covers

Accessory

CAD

Days to Ship

Specify Alterations

Products like this...

Additional Products in this Category

Tech Support

Payment Method

About MISUMI

About this Website

Useful Tools

Customer Service

Social Media

MISUMI Contact 9am – 6pm (Mon – Fri) * Order cut-off time is 5pm, 9am – 1pm(Sat) * Order cut-off time is 12pm