(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- [Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
XYZ-Axis Manual Stages, Linear Ball Guide (E-XYZSG60-R)
- Volume Discount
- XYZ-Axis Manual Stages, Linear Ball Guide type, E-XYZSG series from MISUMI.
- This is an economy item, The price is cheaper than the MISUMI standard product.
- 3 stage sizes are available, 40, 60 and 80 mm.
- The load capacity is 49 N.
- Minimum Reading is 10 μm.
- The material of XYZ-Axis Manual Stages E-XYZSG series are made of D2 Tool Steel with Chemically Nickel Plating surface treatment.
- Can select 4 types of alteration for changing the position of the micrometer knob, Center (A), Side Up (C), Side Down (CU) and Reverse (R).
(i)Caution
- This is an economy item, The price is cheaper than the MISUMI standard product.
Part Number
Configured Part Number is shown.
E-XYZSG60-R
There have been changes to the manual stage drawings for August 2024. Please download the latest drawings and confirm before placing your order!
■ Travel distance
The catalog drawing dimensions are based on a stroke of 0 mm. Using this as a reference, the distance moved in the left and right directions is the travel distance.
■ Load capacity
Refers to the force that the slide table can withstand when the workpiece's center of gravity is located at the center of the slide table, measured in N. If used beyond the load capacity, the slide table may not operate smoothly or may become stuck. When installing the linear motion slide table vertically or upside down, the accuracy may be less than the values indicated in the product catalog. Please take note.
■ Straightness
The maximum deviation of the slide table from the ideal movement axis (the straight line connecting the start and end points, shown as the red line in the diagram below; the black line represents the actual movement path) during full-stroke movement. Measurement method: Place a dial indicator on the slide table with the pointer touching the reference block. Move the slide table through its full stroke and measure the maximum displacement, which is the straightness.
Product Overview
The MISUMI E-XYZSG series linear ball guide type stage is an economical stage. It can be used as a simple position adjustment stage. The main body is made of stainless steel, providing a certain degree of rust resistance. The guide mechanism uses a linear ball guide, which provides the necessary level of accuracy. Due to localized production in China and improved manufacturing processes, the price has been significantly reduced.
Dimensional Drawing
Material Table
| Type |  Material |  Surface treatment |
| Body | SUS440C | Electroless nickel plating |
| Z bracket | Aluminum alloy | Natural anodized |
Alterations
■ Alterations
| Alterations | Change the position of the micrometer knob | |||
| Spec. | Center | Side facing up | Side facing down | Reverse |
| Code | A | C | CU | R |
Specification Table
| Type | Stage surface (mm) | Travel distance (mm) X, Y, Z axes | Load capacity (N) | Straightness (µm) | Minimum reading (µm) | Weight (kg) | |
 Type |  No. | ||||||
| E-XYZSG | 40 | 40 × 40 | ±6.5 | 49 | Within 10 | 10 | 0.78 |
| 50 | 50 × 50 | 1.08 | |||||
| 60 | 60 × 60 | 1.38 | |||||
| 70 | 70 × 70 | 2 | |||||
| 80 | 80 × 80 | ±12.5 | 3 | ||||
■ Travel distance
The catalog drawing dimensions are based on a stroke of 0 mm. Using this as a reference, the distance moved in the left and right directions is the travel distance.
■ Load capacity
Refers to the force that the slide table can withstand when the workpiece's center of gravity is located at the center of the slide table, measured in N. If used beyond the load capacity, the slide table may not operate smoothly or may become stuck. When installing the linear motion slide table vertically or upside down, the accuracy may be less than the values indicated in the product catalog. Please take note.
■ Straightness
The maximum deviation of the slide table from the ideal movement axis (the straight line connecting the start and end points, shown as the red line in the diagram below; the black line represents the actual movement path) during full-stroke movement. Measurement method: Place a dial indicator on the slide table with the pointer touching the reference block. Move the slide table through its full stroke and measure the maximum displacement, which is the straightness.
Product Features
Feature 1: Shortened production lead time, with delivery in as fast as 5 days.
Feature 2: Achieves a low price by simplifying the structure and improving the manufacturing process.
Feature 3: Supports various additional machining options to meet installation requirements in different situations.
Feature 4: Improved clamping mechanism provides greater holding force for the slide table compared to the standard clamping mechanism.
Feature 2: Achieves a low price by simplifying the structure and improving the manufacturing process.
Feature 3: Supports various additional machining options to meet installation requirements in different situations.
Feature 4: Improved clamping mechanism provides greater holding force for the slide table compared to the standard clamping mechanism.
Usage Method
■ Installation method for X-axis slide table
When installing the slide table onto the base, the installation is generally performed by moving the slide table surface. Please refer to the diagram below.
The above diagram is for installation example demonstration only. For detailed shapes and specifications of the slide table, please refer to the respective product catalog or 3D data.
■ Installation orientation
Horizontal, inverted, side horizontal, or side vertical installation can be selected. For other installation methods, please pay special attention.
Depending on the installation orientation, load capacity and accuracy may vary significantly.
○: Same load capacity as horizontal installation.
△: Approximately one-third of the horizontal load capacity is the general standard. If the product catalog lists the vertical load capacity, please give priority to the catalog.
■Vertical Use of X-Axis Stage
When using the X-axis stage vertically, please pay attention to the feed direction and avoid aligning it with the direction of gravity.
When using a micrometer knob type stage, please note that the stage is reset by a tension spring. If the applied force exceeds the spring load, the stage platform may drop. In such cases, additional processing can be selected as a solution.
Please avoid applying loads in the vertical direction that exceed the load capacity.
When installing the slide table onto the base, the installation is generally performed by moving the slide table surface. Please refer to the diagram below.
The above diagram is for installation example demonstration only. For detailed shapes and specifications of the slide table, please refer to the respective product catalog or 3D data.■ Installation orientation
| Diagram |  |  |  |  |
| Installation orientation | Horizontal | Inverted | Side-mounted horizontal | Side-mounted vertical |
| Load resistance characteristics | ○ | ○ | △ | △ |
Horizontal, inverted, side horizontal, or side vertical installation can be selected. For other installation methods, please pay special attention.Depending on the installation orientation, load capacity and accuracy may vary significantly.○: Same load capacity as horizontal installation.△: Approximately one-third of the horizontal load capacity is the general standard. If the product catalog lists the vertical load capacity, please give priority to the catalog.■Vertical Use of X-Axis Stage
When using the X-axis stage vertically, please pay attention to the feed direction and avoid aligning it with the direction of gravity.
When using a micrometer knob type stage, please note that the stage is reset by a tension spring. If the applied force exceeds the spring load, the stage platform may drop. In such cases, additional processing can be selected as a solution.
| Incorrect usage | Correct usage |
| (Generally) If the applied force exceeds the tension load of the spring, the stage platform may fall due to insufficient load capacity. | After selecting the additional machining to change the micrometer knob position, the stage surface will not drop even when used vertically. |
 |  |
Please avoid applying loads in the vertical direction that exceed the load capacity.Precautions
■ Operating temperature and environment
Recommended operating environment: 10–50°C, 20–70% RH (no condensation)
Accuracy-guaranteed environment: 22±5°C, 20–70% RH (no condensation)
■ Guide mechanism
This stage uses a linear ball guide as the guiding mechanism.
■ Clamping mechanism
(1) The clamping mechanism of the stage is fixed by the friction force generated by tightening the screws. Therefore, if an external force exceeding the friction force of the clamping mechanism is applied, the stage will move. Please take appropriate measures during use to prevent the stage surface from moving. If additional clamping reinforcement is required, you can choose either disc clamping or opposed clamping.
(2) Holding force refers to the amount of force that keeps the stage surface from moving when clamped. Since the maximum holding force varies with changes in tightening torque, please ensure a sufficiently large safety factor in your design.
■ Feed Mechanism
A stage equipped with a micrometer knob, as shown in the figure below, is generally referred to as the standard type. The installation space, installation orientation, and operation method can be freely selected. However, due to the structure of the product, there are some models where the installation position of the micrometer knob cannot be changed. For details, please refer to the [Additional Machining] section at the bottom of each product page.
■ Flatness of the mounting surface
The upper and lower slide table surfaces may become deformed due to differences in the flatness of the mounting surface. Deformation of the slide table surface may result in gaps, inability to achieve the specified preload causing looseness, or excessive preload leading to poor sliding performance. Therefore, it is recommended to maintain the flatness of the mounting surface at around 5 micrometers.
Recommended operating environment: 10–50°C, 20–70% RH (no condensation)
Accuracy-guaranteed environment: 22±5°C, 20–70% RH (no condensation)
■ Guide mechanism
This stage uses a linear ball guide as the guiding mechanism.
■ Clamping mechanism
(1) The clamping mechanism of the stage is fixed by the friction force generated by tightening the screws. Therefore, if an external force exceeding the friction force of the clamping mechanism is applied, the stage will move. Please take appropriate measures during use to prevent the stage surface from moving. If additional clamping reinforcement is required, you can choose either disc clamping or opposed clamping.
(2) Holding force refers to the amount of force that keeps the stage surface from moving when clamped. Since the maximum holding force varies with changes in tightening torque, please ensure a sufficiently large safety factor in your design.
■ Feed Mechanism
A stage equipped with a micrometer knob, as shown in the figure below, is generally referred to as the standard type. The installation space, installation orientation, and operation method can be freely selected. However, due to the structure of the product, there are some models where the installation position of the micrometer knob cannot be changed. For details, please refer to the [Additional Machining] section at the bottom of each product page.
■ Flatness of the mounting surface
The upper and lower slide table surfaces may become deformed due to differences in the flatness of the mounting surface. Deformation of the slide table surface may result in gaps, inability to achieve the specified preload causing looseness, or excessive preload leading to poor sliding performance. Therefore, it is recommended to maintain the flatness of the mounting surface at around 5 micrometers.
Example of Use
Mechanism name: Cotton swab glue application position adjustment
Application Industries
| Electronics/Home Appliances | Automotive | Medical | ||
 |  |  | ||
| Smartphones | Semiconductors | Lithium batteries | ||
 |  |  |
Related Products
| Economical Electric Slide Table X-Axis | Economical Electric Slide Table XY-Axis | Economical Electric Slide Table Z-Axis | ||
 |  |  | ||
| Representative model: C-XMBS420-L-A-2 | Representative model: C-XYMBS420-L-A-2 | Representative model: C-ZMBS420-L-A-2 | ||
| Advantage: Low cost, fast delivery | Advantage: Low cost, fast delivery | Advantage: Low cost, fast delivery |
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
| Part Number |
|---|
| E-XYZSG60-R |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Table Size (Length) L (mm) | Table Size (Width) W (mm) | Stroke (X Distance) (mm) | Stroke (Y Distance) (mm) | Stroke (Z Distance) (mm) | Alteration |
|---|---|---|---|---|---|---|---|---|---|---|
MYR 1,909.70 | 1 Piece(s) | Available | 13 Day(s) | 60 | 60 | ±6.5 | ±6.5 | ±6.5 | R [Change feed knob position: reversed] |
Loading...
Basic Information
| Z-Axis Stage Surface | Vertical | Travel Guide | Linear Ball | Feeding Method | Micrometer Head |
|---|---|---|---|---|---|
| Table Material | SUS440C | Table Surface Treatment | Electroless Nickel Plating | Load Capacity(N) | 49 |
| Through Hole (Table Center Hole) | Not Provided | Table Straightness(µm) | 10 |
Please check the type/dimensions/specifications of the part E-XYZSG60-R in the XYZ-Axis Manual Stages, Linear Ball Guide series.
Specification/Dimensions
-
type
- E-XYZSG
-
Table Size (Length) L(mm)
-
Table Size (Width) W(mm)
-
Stroke (X Distance)(mm)
-
Stroke (Y Distance)(mm)
-
Stroke (Z Distance)(mm)
-
Alteration
- A [Change knob position: center]
- C [Change knob position: side]
- CU [Change knob position: side, down]
- R [Change feed knob position: reversed]
- Standard Type
-
CAD
- 2D
- 3D
Days to Ship
-
- All
- 1 Day(s) or Less
- 12 Day(s) or Less
- 13 Day(s) or Less
- 16 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Frequently asked question (FAQ)
- Question: What does the ±XX travel distance of a micrometer knob-type stage mean?
- Answer: The meaning of stroke ±XXmm is how many millimeters can be moved to the left/right or up/down from the midpoint of the full stroke of the micrometer knob.
- Question: What is the reset method for micrometer knob-type manual stages? What should be noted during use?
- Answer: The micrometer knob type manual stage is reset by stretching a spring. If the applied load exceeds the spring load, the slide table may not return to its original position properly, or the spring may be damaged. Please use with caution.
- Question: Can the slide table be installed vertically? What should I pay attention to?
- Answer: Yes, but please note that the load capacity is about one-third when installed horizontally; also, pay attention to the feed direction—do not align it with the direction of gravity. If the applied force exceeds the spring load, the slide table may drop due to insufficient load-bearing capacity.
- Question: Can the manual stage product be used upside down?
- Answer: All except dovetail groove products are available. Dovetail groove products must not be used upside down.
- Question: If the XY-type slide table does not have the size or stroke I want, can I assemble it freely myself?
- Answer: Yes, they can.
Products like this...
| Part Number |
|---|
| E-XYZSG40-CU |
| E-XYZSG40-R |
| E-XYZSG50 |
| E-XYZSG70 |
| E-XYZSG80 |
| E-XYZSG80-A |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Table Size (Length) L (mm) | Table Size (Width) W (mm) | Stroke (X Distance) (mm) | Stroke (Y Distance) (mm) | Stroke (Z Distance) (mm) | Alteration |
|---|---|---|---|---|---|---|---|---|---|---|
MYR 1,694.46 | 1 Piece(s) | Available | 13 Day(s) | 40 | 40 | ±6.5 | ±6.5 | ±6.5 | CU [Change knob position: side, down] | |
MYR 1,694.46 | 1 Piece(s) | Available | 13 Day(s) | 40 | 40 | ±6.5 | ±6.5 | ±6.5 | R [Change feed knob position: reversed] | |
MYR 1,598.27 | 1 Piece(s) | Available | 12 Day(s) | 50 | 50 | ±6.5 | ±6.5 | ±6.5 | Standard Type | |
MYR 1,623.80 | 1 Piece(s) | 16 Day(s) | 70 | 70 | ±6.5 | ±6.5 | ±6.5 | Standard Type | ||
MYR 2,645.92 | 1 Piece(s) | Available | 13 Day(s) | 80 | 80 | ±12.5 | ±12.5 | ±12.5 | Standard Type | |
MYR 2,645.92 | 1 Piece(s) | Available | 13 Day(s) | 80 | 80 | ±12.5 | ±12.5 | ±12.5 | A [Change knob position: center] |
Additional Products in this Category
- [High Precision] Dovetail Slide, Rack & Pinion
- XYZ-Axis Manual Stages, Cross Roller Guide
- XYZ-Axis Crossed Roller Guide Stage
- Dovetail stage feed screw (B08/BDBVS)
- XYZ-Axis Linear Ball Guide (SS) Stage
- Dovetail Type Stage XYZ-Axis
- X/Y/Z-Axis Slim Stage (Manual Stage)
- Manual XYZ-Axis Crossed Roller Bearing Stage
Tech Support
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy