(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- [Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
Sprockets Nominal No.25 (C-SPA25B22-N-15)
- Volume Discount
MiSUMi Economy
- RoHS
Part Number
Configured Part Number is shown.
C-SPA25B22-N-15
Product Overview of Sprockets
■ Sprockets is a solid or spoked gear that engages with a roller chain to transfer motion or power.
Application of Sprockets: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum
■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ANSI 25 Sprockets, and can be used in combination with our 25 series chain.
■ Do not use it with ISO/ANSI B Series chain, which may cause the chain Sprockets mechanism to fail to function properly!
■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.
Actual Product
Application of Sprockets: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum
■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ANSI 25 Sprockets, and can be used in combination with our 25 series chain.
■ Do not use it with ISO/ANSI B Series chain, which may cause the chain Sprockets mechanism to fail to function properly!
■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.
Actual Product
Product Feature of Sprockets
■ Sprockets chain drive has the following features compared with gear drive and belt drive:
1. Sprockets, safe and reliable;
2. Sprockets, Flexible transmission, absorbing shock and vibration;
3. Sprockets, Large center distance range, low manufacturing and mounting accuracy requirements;
4. Sprockets, Compared with belt drive, the transmission ratio is accurate and the transmission efficiency is higher, suitable for high temperature，dusty and humid environments.
■ Sprockets, chain selection
Misumi’s Sprockets and chain product selection supports the principle of “Nominal Numbering”
1. Sprockets, safe and reliable;
2. Sprockets, Flexible transmission, absorbing shock and vibration;
3. Sprockets, Large center distance range, low manufacturing and mounting accuracy requirements;
4. Sprockets, Compared with belt drive, the transmission ratio is accurate and the transmission efficiency is higher, suitable for high temperature，dusty and humid environments.
■ Sprockets, chain selection
Misumi’s Sprockets and chain product selection supports the principle of “Nominal Numbering”
Dimensional Drawing of Sprockets
Product Drawings (Unit: mm)
※ This series is 04C Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 04B series Sprockets.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
| Type |  Material |  Accessories |
| C-SP25B | Equivalent to S45C | Fixing Screw (Only Shaft Hole Specifications N) |
※ This series is 04C Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 04B series Sprockets.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
Usage Method of Sprockets
Example Use of Sprockets
Precautions of Sprockets
■ Sprockets maintenance
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the Sprockets is easy to runout and fall off the chain.
The degree of tightness of the Sprockets is: if lifted up or pressed down from the middle of the Sprockets, the center distance between the two Sprockets is about 2%-3%.
2. The Sprockets shall be installed on shaft without swing and skew.
The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the Sprockets is less than 0.5 meters, the deviation can be 1 mm.
When the center distance of the Sprockets is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on Sprockets tooth side. Integral offset.
If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the Sprockets, you must pay attention to check and adjust the offset
3. After the Sprockets is severely worn, the new Sprockets and the new chain should be replaced at the same time to ensure good meshing.
You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
If the tooth surface of the Sprockets is worn to a certain degree, it should be turned over in time (the Sprockets used with adjustable surface) to extend the life time.
4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
The link should pass through the back of the Sprockets with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.
5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.
6. The old Sprockets cannot be mixed with some of the new Sprockets, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the Sprockets is easy to runout and fall off the chain.
The degree of tightness of the Sprockets is: if lifted up or pressed down from the middle of the Sprockets, the center distance between the two Sprockets is about 2%-3%.
2. The Sprockets shall be installed on shaft without swing and skew.
The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the Sprockets is less than 0.5 meters, the deviation can be 1 mm.
When the center distance of the Sprockets is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on Sprockets tooth side. Integral offset.
If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the Sprockets, you must pay attention to check and adjust the offset
3. After the Sprockets is severely worn, the new Sprockets and the new chain should be replaced at the same time to ensure good meshing.
You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
If the tooth surface of the Sprockets is worn to a certain degree, it should be turned over in time (the Sprockets used with adjustable surface) to extend the life time.
4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
The link should pass through the back of the Sprockets with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.
5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.
6. The old Sprockets cannot be mixed with some of the new Sprockets, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.
Specification Table of Sprockets
| Nominal model | Hub type | Number of Teeth | Shaft Hole Specifications | Shaft Hole Diameter (D) | Dp | D0 | H | L | ℓ | ||||
| S Specifications | N Specifications (H7) | ||||||||||||
| 25 | B | 16 | S N | 9 | 10 | 12 | 32.55 | 36 | 25 | 15 | 6 | ||
| 17 | 9 | 10 | 12 | 34.56 | 38 | ||||||||
| 18 | 9 | 12 | 36.57 | 40 | |||||||||
| 19 | 9 | 12 | 38.58 | 42 | 28 | ||||||||
| 20 | 9 | 10 | 40.59 | 44 | |||||||||
| 21 | 9 | 42.61 | 46 | ||||||||||
| 22 | 9 | 15 | 44.62 | 48 | 30 | ||||||||
| 25 | 9 | 12 | 15 | 50.66 | 54 | 35 | |||||||
| 32 | 10＊ | 64.78 | 68 | 40 | 20 | 8 | |||||||
| 35 | 10 | 70.84 | 74 | ||||||||||
If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm).Shaft Hole Machining Size Table
| Shaft Hole Diameter D | Keyway b2×t2 | Fixing Screw M |
| 10 | 3×1.4 | 4 |
| 10K··12 | 4×1.8 | 5 |
| 15·16 | 5×2.3 | 6 |
| 20 | 6×2.8 | 6 |
Specification Table
| Nominal model | Hub type | Number of Teeth | Shaft Hole Specifications | Shaft Hole Diameter (D) | Dp | D0 | H | L | ℓ | ||||
| S Specifications | N Specifications (H7) | ||||||||||||
| 25 | B | 16 | S N | 9 | 10 | 12 | 32.55 | 36 | 25 | 15 | 6 | ||
| 17 | 9 | 10 | 12 | 34.56 | 38 | ||||||||
| 18 | 9 | 12 | 36.57 | 40 | |||||||||
| 19 | 9 | 12 | 38.58 | 42 | 28 | ||||||||
| 20 | 9 | 10 | 40.59 | 44 | |||||||||
| 21 | 9 | 42.61 | 46 | ||||||||||
| 22 | 9 | 15 | 44.62 | 48 | 30 | ||||||||
| 25 | 9 | 12 | 15 | 50.66 | 54 | 35 | |||||||
| 32 | 10＊ | 64.78 | 68 | 40 | 20 | 8 | |||||||
| 35 | 10 | 70.84 | 74 | ||||||||||
If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm).Shaft Hole Machining Size Table
| Shaft Hole Diameter D | Keyway b2×t2 | Fixing Screw M |
| 10 | 3×1.4 | 4 |
| 10K··12 | 4×1.8 | 5 |
| 15·16 | 5×2.3 | 6 |
| 20 | 6×2.8 | 6 |
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
| Part Number |
|---|
| C-SPA25B22-N-15 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Number of Teeth (T) | Shaft Bore Dia. D (or d) (mm) | Type | Shaft Type | Bore Specification |
|---|---|---|---|---|---|---|---|---|---|
MYR 21.16 | 1 Piece(s) | 1 Day(s) | 22 | 15 | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) |
Loading...
Basic Information
| Sprocket Shape | Shape B | Nominal | 25 | Number of Strands | 1 |
|---|---|---|---|---|---|
| Material | S45C | Chain Type | RS | Surface Treatment | Not Provided |
Please check the type/dimensions/specifications of the part C-SPA25B22-N-15 in the Sprockets Nominal No.25 series.
Specification/Dimensions
-
type
- C-SPA25B
-
Number of Teeth(T)
-
Shaft Bore Dia. D (or d)(mm)
-
Type
- Pilot Bore Type
- Shaft Bore Machined Type
-
Shaft Type
- Standard Pilot Bore
- Shaft Bore Machining Configurable
-
Bore Specification
- N (New JIS Key + Screw Bore Type)
- S (Through Hole)
-
CAD
- 2D
- 3D
Days to Ship
-
- All
- 1 Day(s) or Less
- 10 Day(s) or Less
- 15 Day(s) or Less
- 16 Day(s) or Less
- 69 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Frequently asked question (FAQ)
- Question: I bought MISUMI chains, but why can't I use them on my original sprocket?
- Answer: Please confirm the specifications of the original sprocket and chain. Specification series number may not match. In addition, there are two specifications: A series and B series in China. The two specifications of sprocket chain are not universal.
- Question: Does the sprocket need routine maintenance after installation and use?
- Answer: The chain needs regular maintenance after installation and use. These include daily lubricant application, confirmation of chain slack. After the sprocket is severely worn, the new sprocket and the new chain should be replaced at the same time to ensure good meshing.
- Question: I need to use two overlapped sprockets, I want the tooth top direction to be consistent, is it possible?
- Answer: Due to process reasons, it is impossible to guarantee the overlapping of the tooth tops of several sprockets. If the tooth tops are required to be overlapped, please contact our company or indicate on the order (the tooth tops need to be overlapped)
- Question: The engraving on the sprocket does not match the packaged model, is it shipped wrongly?
- Answer: The product model is subject to the label on the shipping bag and the actual size. The engraving is only the factory management number of the sprocket product during processing, and is not directly associated with the product model.
Products like this...
| Part Number |
|---|
| C-SPA25B16-N-10K |
| C-SPA25B16-N-12 |
| C-SPA25B17-S-9 |
| C-SPA25B19-N-12 |
| C-SPA25B32-S-10 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Number of Teeth (T) | Shaft Bore Dia. D (or d) (mm) | Type | Shaft Type | Bore Specification |
|---|---|---|---|---|---|---|---|---|---|
MYR 15.09 | 2 Piece(s) | Available | 10 Day(s) | 16 | 10 | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | |
MYR 15.71 | 2 Piece(s) | Available | 10 Day(s) | 16 | 12 | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | |
MYR 24.03 | 1 Piece(s) | 16 Day(s) | 17 | 9 | Pilot Bore Type | Standard Pilot Bore | S (Through Hole) | ||
MYR 18.63 | 1 Piece(s) | 69 Day(s) | 19 | 12 | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 70.12 | 2 Piece(s) | Available | 15 Day(s) | 32 | 10 | Pilot Bore Type | Standard Pilot Bore | S (Through Hole) |
Additional Products in this Category
- FBN50B finished bore sprocket
- SUS Standard Stainless Steel 2050 Double Pitch Sprocket For S Roller B Type
- Stainless Steel Sprocket 40B Type
- Stainless steel sprocket type 60B
- Standard 2100 Double Pitch Sprocket, S Roller B Type
- Standard Sprocket, Model 25A
- Standard Sprocket, Model 50A
- MS SW (Double-Single) Sprocket With Shaft Bore Processing
Tech Support
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy