(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
Nozzles with Swaged Sleeve Couplings
- Volume Discount
"Can blow the air from the copper pipe efficiently, by attaching to the pipe."
(i)Caution
- Please check the content on our website as the PDF does not contain the most up-to-date information.
Part Number
Configured Part Number is shown.
| SKNS | SKNF | |
 |  |
| Type | [M] Material | Heat Resistance Temperature |
| SKNS | Ferrule: SUS304 Others: SUS304 | 200°C |
| SKNF |
Specification Table
| Part Number | — | d |
| SKNS4 | — | 1.5 |
| SKNF6 | — | 1 |
| Part Number | Orifice d Selection | (L) | B | A | Square | Mass (g) | ||||
| Type | Applicable Pipe O.D. D | Main Body | Nut | |||||||
| SKNS | 4 | 1.0 | 1.5 | 2.0 | 25.3 | 9 | 4 | 14 | 12 | 15 |
| 6 | 1.5 | 2.0 | 3.0 | 30.6 | 12 | 5.5 | 14 | 13 | 20 | |
| 8 | 2.0 | 3.0 | 5.0 | 37 | 13 | 8 | 19 | 17 | 38 | |
| SKNF | 4 | 0.8 | 1.0 | 1.2 | 24.2 | 8 | 4 | 13 | 12 | 15 |
| 6 | 28.4 | 10 | 5.5 | 14 | 13 | 20 | ||||
| 8 | 38 | 14 | 8 | 19 | 17 | 40 | ||||
| ■Tightening Procedure of Fittings | ||
 | (1) Insert the pipe into the fitting until the pipe tip contacts the shoulder inside without removing the nut. (2) Hand-tighten the nut until it stops turning. Mark this position as the ○ point. (3) Secure the fitting body tightly with a wrench and tighten the nut with another wrench by the number of turns shown on the right. CAUTION: For plastic tube connections, be sure to use a tube insert (SKITK) and tighten φ4 to φ12.7 tubes by 1 1/4 to 1 1/2 rotations. | φ4 Type φ6 to φ12.7 Type  |
| ■How to Tighten after Removing | ||
 | (1) Be sure to confirm the position of the nut before loosening and removing it. (Standard tightening position) Make sure that front ferrule is installed in the correct position. Make sure that there are no foreign objects on the tapered surface, front and rear of the body before reinstallation. (2) Insert all the way until the front ferrule fully contacts the tapered seat surface of the body, tthen hand-tighten the nut. (Insert carefully to avoid the tapered part on the main body being scratched by the pipe end.) (3) Using a wrench, tighten slightly past the position before loosening. | Position before tightening the nut Retightened position  |
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
| Part Number |
|---|
| SKNF4-0.8 |
| SKNF4-1.0 |
| SKNF4-1.2 |
| SKNF6-0.8 |
| SKNF6-1.0 |
| SKNF6-1.2 |
| SKNF8-0.8 |
| SKNF8-1.0 |
| SKNF8-1.2 |
| SKNS4-1.0 |
| SKNS4-1.5 |
| SKNS4-2.0 |
| SKNS6-1.5 |
| SKNS6-2.0 |
| SKNS6-3.0 |
| SKNS8-2.0 |
| SKNS8-3.0 |
| SKNS8-5.0 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | RoHS | Shape | Air Flow Rate (at 0.3MPa) (NL/min) |
|---|---|---|---|---|---|---|---|
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 70 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 103 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 112 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 196 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 221 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 234 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 243 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 264 | |
MYR 68.76 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Slit on Tip | 287 | |
MYR 63.26 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 12 | |
MYR 63.26 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 59 | |
MYR 63.26 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 113 | |
MYR 63.81 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 55 | |
MYR 63.81 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 112 | |
MYR 63.81 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 162 | |
MYR 64.90 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 123 | |
MYR 64.90 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 200 | |
MYR 64.90 | 1 Piece(s) | Available | 4 Day(s) or more | 10 | Single Hole on Tip | 258 |
Loading...
Specifications / Overview
App. Example
(Cleaning of workpiece)
Basic Information
| Spray Shape | Point | Material | SUS304 | Angle Adjustment | Straight |
|---|---|---|---|---|---|
| Attaching Type | Swaged |
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Additional Products in this Category
- Terminals for Nozzles - Clamp Type
- Flat Air Nozzles - For Blowers
- Spray Nozzles, Circular Spray Pattern - Standard
- [Clean & Pack]Nozzles with Swaged Sleeve Fitting
- Insert Nozzle JT Type (Mounting Parts Angle Type)
- Insert Nozzle PM Type
- Nozzle Angle Adjustment Bar
- Air/Steam Type Flat Fan-Shaped Nozzle, VZ Series (Compressor Specification)
Customers Who Viewed This Item Also Viewed
-
-
-
-
-
-
-
-
-
Single Type Air Jet Nozzle KSVEVERLOY
Standard Price : MYR 195.84-
Days to Ship : 10 Day(s) or more
-
-
-
Spray Nozzles, Circular Spray Pattern - Air Amplified TypeMISUMI
Standard Price : MYR 123.76-
Days to Ship : 4 Day(s) or more
Tech Support
- Factory Automation, Electronics, Tools, & MRO (Maintenance, Repair and Operations)
- Tel：(60) 3 7890 6399
- 9:00am - 6:00pm (Monday - Friday)
9:00am - 1:00pm (Saturday) - Technical Inquiry
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy